Events
Events
Events
Events
Events
Events
Events
Events
Events
Events
MY FS FLIGHTS
Flight Score
Maintain a smooth pitch
Next time
Raise the gear promptly once a positive rate is confirmed, before reaching the gate altitude.
What happened: Gear retraction was late relative to the target height for this stage of the climb.
Watch for: Landing gear position against the retraction height gate.
When Vr arrives, an abrupt near-full-scale pull, pitch overshoots, a push, and an oscillation through the first 200 ft. It feels like “this aircraft is twitchy” but the actual fault happened before liftoff. The pitch trace needs to show a clean ramp during liftoff.
Read more in Improve Your Take-OffsStart to finish · 15 stages, 13 scored
Events
Events
Events
Events
Events
Events
Events
Events
Events
Events
The threshold, the flare and the hold-off. The approach that led to it is the stabilisation gates below.
Two stabilised approach gates, each with seven checks, where the approach path is 1,000 ft and 500 ft above the runway. They are the approach's score: the checks passed out of the checks that ran.
At the 500 ft gate: sink rate 1,094 fpm, more than the glideslope needed.
The approach, gate by gate
Side view — the last 1,524 m of the approach.
Plan view — the first 1,524 m of the 2,588 m runway, to the same scale as the side view.
The 485 m touchdown sits inside the full-score zone. The arrival was smooth.
The rest of the report
The Boeing 737-800 taxied from the parking area to the runway in 7 minutes, covering approximately 1 nm.
The aircraft commenced its departure roll on runway 28 at LIME Milan Bergamo Airport / Antonio Locatelli Air Base, using a takeoff distance of 1,731 m which represented 63 % of the runway length; liftoff was achieved at 156 kt and the ambient temperature was 22 deg C.
Climb began overhead Orio al Serio in Lombardia, Italy, with the flight ascending from 1,545 ft asl to 35,982 ft asl - an increase of 34,437 ft - over 18 minutes while covering 111 nm.
Level cruise was established 1 mile west of Lana in Trentino-Alto Adige, Italy, and persisted for 104 minutes, during which 766 nm were flown.
Descent was initiated 6 miles north-east of Dronninglund in the North Denmark Region, Denmark, descending from 36,007 ft asl to 1,524 ft asl - a loss of 34,483 ft - in 21 minutes and traversing 116 nm.
The final approach to runway 36 at ENTO Sandefjord Airport, Torp was conducted from the south, on a heading of 360.0 deg at 4 nm and 1,246 ft agl.
Landing on runway 36 at ENTO Sandefjord Airport, Torp employed a runway length of 2,588 m; the threshold speed was 146 kt, touchdown occurred 72 m beyond the touchdown zone at 138 kt, and the vertical speed at touchdown was minus 20 fpm. The local temperature was 15 deg C.
The aircraft rolled out over a distance of 1,285 m, representing 50 % of the runway, with alignment maintained throughout the rollout.
Taxi-in to the parking area from the runway required 3 minutes and covered less than 1 nm.
In total, the flight covered 1,000 nm, required 155 minutes of elapsed time, and consumed 3,849 kg of fuel.
The Airbus A321neo completed the final approach to runway 16R at KSLC from the north, tracking a heading of 175.0° at 4 nm and 1,406 ft agl. The approach was assessed as stabilised at the 1,000 ft gate, with gear, flaps, sink rate, glideslope and centreline all within limits, and the local weather was 18 °C with wind 13 kt from 140°, including a 7 kt crosswind and a 10 kt headwind.
During the threshold and flare phase the threshold height was good and the threshold speed was good at 142 kt. Touchdown distance was good at 327 m, while touchdown speed at 140 kt was a little fast.
Touchdown occurred with a firm rate of minus 363 fpm and the aircraft landed 7.8 m off the centreline. Total landing distance was 1,473 m, representing 40 % of the 3,655 m runway.
Rollout alignment was very good, with the aircraft remaining on the centreline throughout the remaining distance.
With a final score of 94.8 % the landing was strong; refining flare timing to reduce touchdown speed and tightening lateral control to eliminate the 7.8 m offset will bring the performance to an even higher standard.
Scroll or drag the slider to zoom · double-click to reset · hover for values