Events
Events
Events
Events
Events
Events
Events
Events
Events
Events
Events
MY FS FLIGHTS
Flight Score
Configure earlier
Preparing for a stable approach will give you time to decide on whether to attempt the landing or going around. Too much altitude with a high sink rate will result in carrying too much speed onto the runway. Configuring flaps and the gear late also won't help the speed decay.
Read more in The Stabilised ApproachStart to finish · 19 stages, 17 scored
Events
Events
Events
Events
Events
Events
Events
Events
Events
Events
Events
Two stabilised approach gates, each with six checks at 1,000 ft and 500 ft above the runway.
The approach, gate by gate
Side view — the last 960 m of the approach.
Plan view — the full 960 m runway, to the same scale as the side view.
The 244 m touchdown sits inside the full-score zone. The arrival was smooth.
The rest of the report
Taxiing from the parking area to the runway at Toronto Lester B. Pearson International Airport (CYYZ) took approximately 4 minutes, covering less than 1 nautical mile. Departure roll commenced on runway 23, with the aircraft clearing the runway threshold at 1,079 meters, utilizing 34% of the available runway length. Liftoff speed was achieved at 97 knots, as the aircraft began its takeoff roll.
Following departure, the aircraft initiated its enroute climb approximately 1 mile west of CYYZ, ascending from 1,554 feet above sea level to 26,937 feet above sea level, an increase of 25,383 feet, in 13 minutes and covering 40 nautical miles. The enroute level cruise phase commenced 4 miles northwest of Shelburne (CSF4), lasting 11 minutes and covering 47 nautical miles. Subsequently, the aircraft entered its enroute descent phase, initiated 3 miles west of East Linton (CEL3), descending from 27,206 feet above sea level to 1,803 feet above sea level, a decrease of 25,403 feet, in 16 minutes and covering 68 nautical miles.
The final approach to runway 30 at Tobermory Airport (CNR4) was initiated from the east, with the aircraft maintaining a heading of 264.0° at 3 nautical miles and 1,103 feet above ground level. However, a go-around was executed at 1,186 feet above ground level. The aircraft subsequently landed on runway 30, with a touchdown distance of 243 meters, utilizing 53% of the available runway length. The touchdown speed of 86 knots was slightly above the target, while the touchdown rate of -227 feet per minute was fair. Runway touchdown alignment was very good, and the runway rollout alignment was also satisfactory. Taxiing from the runway to the parking area took approximately 1 minute, covering less than 1 nautical mile. The total flight distance was 161 nautical miles, with a total flight time of 51 minutes, and the aircraft utilized 156 kilograms of fuel.
The aircraft touched down on runway 30 at CNR4 Tobermory Airport with a good threshold height, allowing for a stable approach. The final approach was initiated from the east, heading 264.0° at 3 nm and 1,103 ft above ground level. The pilot maintained a steady descent, with the threshold speed exceeding the target at 94 kt. This slight excess in speed was not detrimental to the overall landing performance.
As the aircraft made contact with the runway, the touchdown distance was satisfactory at 243 m, with a touchdown speed of 86 kt, which was a little fast. However, the touchdown rate of -227 fpm was fair, indicating a controlled descent. The runway touchdown alignment was very good, with the aircraft centered on the runway. The local weather conditions, with a temperature of -0 °C and a wind of 17 kt at 308°, contributed to a relatively stable approach.
The aircraft's rollout was smooth, with the runway rollout alignment being very good. The total landing distance of 508 m was 53% of the runway length, indicating a controlled deceleration. Overall, the landing performance was satisfactory, with a score of 97.0%. The pilot's ability to maintain a stable approach and controlled touchdown was evident, despite the slight excess in touchdown speed.
Scroll or drag the slider to zoom · double-click to reset · hover for values