Events
Events
Events
Events
MY FS FLIGHTS
Flight Score
Departure
Ease the yoke smoothly to hold a steady one g through the ground roll instead of letting it sag to 0.4 g.
What happened: During the ground roll the g force averaged 0.4 g, well below the smooth steady load expected while tracking the runway.
Watch for: Watch the g meter and hold it steady near one g through the roll.
See Departure Roll
When Vr arrives, an abrupt near-full-scale pull, pitch overshoots, a push, and an oscillation through the first 200 ft. It feels like “this aircraft is twitchy” but the actual fault happened before liftoff. The pitch trace needs to show a clean ramp during liftoff.
Read more in Improve Your Take-OffsStart to finish · 11 stages, 10 in the score
Events
Events
Events
Events
Taxi out
The roll
A clean takeoff
Rotated at 95 kt against the 97 kt rotate speed.
Rotated on speed at a steady rate, and the climb attitude held. This is the takeoff to repeat: the same speed check, the same pull, the same attitude.
Liftoff and climb
Plan view the roll down the 1,101 m runway.
Rolled from 293 m in, drifted 3.5 m right of the centreline and was back on it to lift off, in 21 kn of crosswind from the right. Airborne 44 % of the way down the runway, before the 75 % line.
The roll from above, with your left at the top. The line is where the wheels went, and "widest" is the furthest you drifted off the centreline. Lifting off before the amber 75 % line gets full marks for the roll length. The arrow beside the runway is the crosswind, pointing the way the air was moving, so it pushed the aircraft that way.
Side view from the start of the roll to 47 ft.
Reached 35 ft with 405 m of runway left.
The takeoff from the side: the height above the runway against the distance along it. The numbers along the runway are the speeds reached at each point. Lifting off in the amber last quarter of the runway costs marks for the roll length.
Speed and pitch from brake release to the end of the climb, against time.
Two traces from brake release: the airspeed on top, and below it the pitch, which is how far the nose is above the horizon. The figure at liftoff is the pitch then.
The threshold, the flare and the hold-off. The approach that led to it is the stabilisation gates below.
Right-hand, 1,000 ft circuit height. The plan shows your circuit over a textbook one for this runway; the profile unrolls the same path from liftoff to the threshold.
Plan landing direction to the left; in pale blue the textbook circuit for your downwind speed, 1.1 nm out at 112 kt
The lap from above, with the landing direction to the left: the opposite of the runway drawings. The wide pale-blue line is a textbook circuit for your downwind speed - the downwind a mile out for every 100 kt, every turn at 30° of bank - and your track is drawn over it, each leg in the colour of its mark. The numbers are the four turns, the same as on the profile and the cards below. The 45° line from the threshold is the usual point to turn onto base.
Around the circuit height and bank; the turns are shaded
The same lap straightened out, so the height and the bank can be read together. Each shaded stretch is a turn, numbered as on the plan. The green box is circuit height, 1,000 ft, on the downwind. The amber line is 30° of bank, and a turn's steepest bank shows red above 32°. "Turn crosswind from" is the lowest height to start the first turn at.
Rough: the G force varied more than a smooth turn and leg would.
Each lap slightly wider and higher than the last, because you're unconsciously using the previous lap as your reference instead of the runway and the numbers. Invisible lap to lap, unmistakable across ten. This is the failure that only measurement catches, because your memory of lap three is gone by lap eight.
Read more in Pattern WorkGood: full marks on the turn and the leg after it.
Off heading: 9° from the leg's heading on average.
Bank angle in the pattern is conventionally kept to 20 to 30 degrees, and the base-to-final turn is where that convention earns its keep. Stall speed rises with bank because the wing must produce more lift in a turn. Roughly 7 per cent higher at 30 degrees, about 19 per cent at 45, and around 40 per cent at 60. At 65 kt on base you don't have much margin to spend steepening a turn to salvage an overshoot.
Read more in Pattern WorkSteep: 40° of bank.
From abeam the threshold, fly roughly 30 to 45 seconds before turning base, in nil wind at 172 speeds. Treat that as a starting value and calibrate it. If your finals keep coming out at 400 ft instead of 500, add a few seconds. Then adjust for wind, roughly a second per knot of headwind on final (a headwind on final is a tailwind on downwind, carrying you further from the field per second).
Read more in Pattern WorkThe rest of the report
The flight began with a departure roll on runway 12 at LFLI Annemasse Airfield. The local weather was a temperature of 12 °C and a wind of 21 kt from 205°, giving a crosswind of 21 kt and a headwind of 1 kt. The takeoff distance was 556 m, which was 50 % of the runway. Liftoff speed was 95 kt.
The initial climb to 50 ft agl took 3 seconds, averaging 907 fpm, and the aircraft reached 106 kt at the top.
The aircraft then flew a right-hand circuit from runway 12, which took 4 minutes. The downwind leg covered 3 nm in 99 seconds at 1,030 ft agl. The base leg was less than 1 nm and took 16 seconds.
The final approach to runway 12 began at 794 ft agl, and the descent to 17 ft agl took 56 seconds. The approach was not scored on a circuit, so the stabilisation gate is shown for reference only. At the 500 ft gate above the runway, the checks for gear down, landing flap, sink rate and on glideslope were met. The on speed check was not met.
At the threshold of runway 12, which is 1,101 m long, the threshold height was good. The threshold speed was too high at 95 kt. The flare was good, but the aircraft dropped onto the runway at the end of it. No bounce or rollout details were provided.
The total flight distance was 8 nm, taking 5 minutes and using 2 kg of fuel.
Scroll or drag the slider to zoom · double-click to reset · hover for values