Events
Events
Events
Events
Events
Events
Events
Events
MY FS FLIGHTS
Flight Score
Hold the glidepath
Preparing for a stable approach will give you time to decide on whether to attempt the landing or going around. Too much altitude with a high sink rate will result in carrying too much speed onto the runway. Configuring flaps and the gear late also won't help the speed decay.
Read more in The Stabilised ApproachStart to finish · 16 stages, 14 scored
Events
Events
Events
Events
Events
Events
Events
Events
The threshold, the flare and the hold-off. The approach that led to it is the stabilisation gates below.
Two stabilised approach gates, each with six checks, where the approach path is 1,000 ft and 500 ft above the runway. They are the approach's score: the checks passed out of the checks that ran.
At the 1,000 ft gate: speed 32 kt FAST on the reference speed of 113 kt.
At the 500 ft gate: glideslope 1.7° against the runway's 3°.
The approach, gate by gate
Side view — the last 5,000 ft of the approach.
Plan view — the first 5,000 ft of the 12,795 ft runway, to the same scale as the side view.
The 1,164 ft touchdown sits inside the full-score zone. The arrival was smooth.
The rest of the report
Departing from Chattanooga Metropolitan Airport (Lovell Field), the aircraft began its journey on runway 33, accelerating down the 7,000-foot-long runway in 1,919 feet, or 39% of its length, before lifting off at a speed of 141 knots. The local weather conditions at the time of departure were characterized by a temperature of 61°F and a gentle headwind of 1 knot, with a crosswind of 2 knots from the west.
As the aircraft climbed out of Lovell Field, it began its enroute climb, reaching an altitude of 30,007 feet in 14 minutes, covering a distance of 88 nautical miles. The climb was initiated 1 mile east of East Chattanooga, and the aircraft continued to ascend to its cruising altitude. Following a 42-minute level cruise, during which the aircraft covered 367 nautical miles, it began its descent, reducing its altitude from 29,998 feet to 2,948 feet in 16 minutes, covering a distance of 94 nautical miles. The final approach to Topeka Regional Airport was initiated from the southeast, with the aircraft aligning with runway 31 and touching down at a speed of 100 knots, with a smooth touchdown rate of -118 feet per minute.
The landing distance of 1,159 feet was well within the acceptable range, and the runway touchdown position was only slightly misaligned from the centerline. The total landing distance of 2,703 feet, or 21% of the runway length, was also within the acceptable range. Following a smooth rollout, the aircraft taxied to the parking area, completing its journey of 562 nautical miles in 81 minutes, with no fuel consumption reported.
The aircraft, C750, successfully executed a final approach to runway 31 at KFOE Topeka Regional Airport from the south east, aligning with the runway heading of 317.0° at a distance of 4 nautical miles and an altitude of 1,238 feet above ground level. The approach quality was satisfactory, with a good threshold height achieved. However, the threshold speed was slightly below the target, registering at 105 knots.
Upon touchdown, the aircraft demonstrated good performance, with a touchdown distance of 1,159 feet and a touchdown speed of 100 knots. The touchdown rate was smooth, at -118 feet per minute. Although the runway touchdown position was slightly misaligned from the centreline by 23 feet, the overall touchdown characteristics were good. The local weather conditions, with a temperature of 59°F and a light wind of 2 knots at 270°, contributed to a relatively stable approach and landing.
The total landing distance of 2,703 feet, which accounted for 21% of the runway length, was within acceptable limits. The runway rollout alignment was very good, indicating a high level of control and precision during the landing phase. Overall, the landing performance of C750 scored 98.0%, reflecting a high level of proficiency and adherence to standard operating procedures.
Scroll or drag the slider to zoom · double-click to reset · hover for values